ELSYS
TPCE
Elsys TPCE DAQ 카드는 복잡한 트리거 기능, 연속 데이터 수집 모드, 차동 또는 단일 종단 입력, 디지털 마커 입력, 피에조 센서용 ICP/IEPE 공급을 갖춘 고정밀 및 고해상도 디지타이저/데이터 수집 카드입니다.
다양한 TPCE 카드는 짧은 PCI Express(PCIe) 형식으로 제공됩니다. 하나의 모듈로 확장 가능한 측정 시스템을 시작할 수 있습니다. 필요한 경우 하나의 하우징에서 최대 64개 채널로 확장할 수 있습니다.
-
TPCE
High-Speed Data Acquisition Card
The Elsys TPCE DAQ cards are high precision and high resolution digitizer/data acquisition cards with complex trigger capabilities, a continuous data acquisition mode, differential or single-ended inputs, digital marker inputs as well as ICP/IEPE supply for piezo sensors.
The various TPCE cards are in the short PCI Express (PCIe) format. A scalable measurement system can be started with one module. If required, expansion with up to 64 channels in one housing is possible.
-
DAQ
- Up to 240 MS/s sampling rate
- 14- and 16 Bit vertical resolution
- Available in 4 variants: 4 / 8 channel single ended or differential inputs
- High precision of typ. 0.03 % of the input range
- 100 mV to 100 V Input Range
- 0 to 100 % Offset
- low noise
- High differential CMRR
- Anti Aliasing Filter (optional)
- IEPE/ICP 4mA current source (optional)
- Various trigger options
- Up to 1 GB memory
(128 MS per channel) - PCIe 1.1, x4 lane, 2.5 GB/s
(10x faster then the PCI-Bus) - Continuous data recording with up to 120 MS/s per channel.
- Short PCIe Format
Variants
The TPCE as well as the TPCE-LE are available in 4 different variants with different number of channels and input configurations.
- 4S: 4 Single Ended inputs, can also be used as 2 differential inputs.
- 8S: 8 Single Endedinputs, can also be used as 4 differential inputs.
- 4D: 4 differential inputs,can also be used as 4 Single Ended input.
- 8D: 8 differential inputs,can also be used as 8 Single Ended input.
For 8-channel cards, the on-board memory per channel is halved (16 MS instead of 32 MS or optionally 64 MS instead of 128 MS)
IEPE / ICP Supply
(Optional)
Each input of the TPCE or TPCE-LE data acquisition board can be equipped with an individual 4 mA current source. This allows IEPE/ICP piezo sensors to be operated directly with the card without any additional hardware.
What is IEPE/ICP®?
IEPE is an abbreviation meaning “Integrated Electronics Piezo-Electric”. A semiconductor circuit converts the high-impedance signal of the piezo sensor into a low-impedance voltage signal that is easier to transmit. Thanks to IEPE, power supply and signal transmission can be realized with only one standard cable of any length, without measurement errors caused by cable movements. The IEPE principle is known under various more proprietary names such as ICP®, Piezotron®, CCLD, IsoTron® or DeltaTron®.
Where and how IEPE/ICP® is applied?
IEPE can be used for force, pressure and acceleration sensors. Thanks to the integrated signal conversion, IEPE sensors are easier to handle and less sensitive to electrical interference than piezoelectric sensors without IEPE. However, the semiconductor circuit used limits their use to a temperature range of max. 150 to 200°C.
-
-
TPCE datasheet